MODEL NO: 299850, 299851, 299852, 299858, 299859, 299860

Remote Temperature Controllers

1

YEAR
WTY

  • Rheem Bathroom Controllers can be set up to 50°C.

  • Deluxe Controllers offer a “bath fill” mode, which turns off the water flow once the bath is filled – at exactly the temperature you set.

  • Rheem Standard and Deluxe Electronic Temperature Controllers are optional on all Continuous Flow models allowing you to choose the exact temperature you need and to guard against scalding.

Features at a Glance

Capacity (L)
0
No. of People
0
Energy Rating
n/a

To install a Rheem, you'll need a plumber

Get in touch with your local Rheem Approved Plumber and ensure your install is done right.

To obtain a quote on this product

Call Rheem on


Ready to buy a Rheem?

For help to make the right choice, access our network of Rheem Approved Plumbers and Stockists.


Top Five Troubleshooting Topics


Please see the Owner Guide for your Solar Hot Water System model.

The error code is displayed on the LED display panel on the front of your continuous flow water heater. Please refer to the below listing to see what your error codes means, then call Rheem Service to book a service call on 13 10 31.

 

Error Code

Fault Condition

Items To Check

03

EZ Link

Book service call

05

Imperfect Combustion Alarm

10

Abnormal low rate combustion

11

Ignition failure at start up

LPG users check Propane bottle level. Close hot tap, cycle power on and off at GPO and open hot tap again. If fault re-occurs book service call.

12

Flame failure during operation

14

Over heating

Book service call

 

15

Very high temperature

16

Outlet water temp too high

24

Operational switch faulty

29

Heat Exchanger Outlet Temp. Too Low

31

Inlet thermistor open circuit

32

Heat exchanger thermistor open circuit

33

Outlet thermistor open circuit

34

Ambient air thermistor open circuit

35

Thermistor connections crossed

51

Gas cut off malfunction (SV0 failure)

52

P.G.F.R control failure

56

Bypass solenoid failure

61

Abnormal fan speed or fan failure

65

Malfunction of water volume control motor

66

Water By-Pass Control Fault

71

G.I.S valve control failure

72

Detected false flame

73

Vent type control data failure

74

Communication problem between remote controller and water heater

75

76

79

Fan motor current detection failure

80

Gas cut off defective

81

No false flame detected

82

Functional problem on gas type circuit board

90

Decrease in fan motor ventilation.

99

Decrease in fan motor ventilation. (Operation stop)

Please contact your electricity provider to confirm the times when you pay off-peak, shoulder and peak tariffs for your electricity. Your water heater will be connected to an appropriate tariff (timed control), depending on its capacity, to ensure you have sufficient hot water for your needs. Twin element water heater models have the added benefit of using off peak tariffs to save money whilst providing an extra boost should it be needed. Please see the Owner Guide for your Storage Water Heater model.

Please see the Owner Guide for your Storage Water Heater model and our gas relighting videos. 

Please locate your model number, serial number and the date of manufacture, found here, for your Rheem hot water system and call Rheem on 1300 556 036.


Is the gas connection only used for the Water Heater?

Please, select all the fields

Running Cost Estimator Disclaimer as at 23/10/2017

Things that you should know about the Rheem Running Cost Estimator

The estimator is provided as a guide only to help you compare estimated running costs between various water heater types.

The estimator is based on Australian Standard AS5263, which relies on certain assumptions, such as an average daily load of 200L and 19 tap turns. Your situation and usage may be different to these assumptions, so the estimator may not match your actual daily loads and pattern of use.

Accordingly, the estimator cannot and does not purport to provide an accurate assessment of your yearly hot water energy bill. It does, however, allow a reasonable comparison between various water heater types based on Australian Standard AS5263 and average fuel tariffs used in the estimator.

Your state has been used to determine the temperature rise required to heat water from cold to a temperature of 65C, the applicable charge for the tariff type selected and the amount of solar savings.

Solar savings are based on Australian Government approved modelling for the type of solar water heater selected and the booster type. All electric boosted solar water heaters are modelled with a continuous tariff, but may be suitable for use on other tariff types depending on the model selected, your climate zone and the amount and usage pattern of hot water use.

Tariffs are current as at 1st July 2017 and represent an average price for the fuel type for the capital city in the state or territory, including GST.

Fixed charges, system access charges, delivery fees and any other fees and charges, including special rates and discounts are excluded from the estimator.

Energy consumption figures used are for a typical water heater within a category and do not reflect a specific model. Actual energy use may vary.

Heat Pump and solar water heaters may be suitable for Off Peak/Shoulder Rate tariffs depending on the type of water heater selected and the location. You should consult with your energy provider or installer before making any decision.

Continuous Flow Brochure 2018


Recess Boxes

To help protect the water heater and set your Rheem into the wall.

Rheem EZiSET® kit

With the NEW Rheem EZiSET® app, controlling your hot water has never been easier.

Save when switching to solar


To install a Rheem, you'll need a plumber

Get in touch with your local Rheem Approved Plumber and ensure your install is done right.


Ready to buy a Rheem?

For help to make the right choice, access our network of Rheem Approved Plumbers and Stockists.